weberfloor 4761N Epoxy Coating
weberfloor 4761N Epoxy Coating
weberfloor 4761N epoxy coating is high-quality adjusted, with very good coverage. Due to the low viscosity the product is suitable for rolled coatings, as well as top sealing coat for scattered, slip resistant coatings.
Packaging
- Bucket-Combi 10 kg, Hobbock-Combi 30 kg
weberfloor 4761N epoxy coating is an all-purpose, solvent-free, pigmented, 2-component epoxy resin coating for hard-wearing industrial coatings.
weberfloor 4761N epoxy coating is high-quality adjusted, with very good coverage. Due to the low viscosity the product is suitable for rolled coatings, as well as top sealing coat for scattered, slip resistant coatings.
The material is suitable for smooth coatings for 1 - 4 mm layers. The coating material may be mixed with fire-dried quartz sand (grain size 0.1/0.3 mm) up to 0.7 parts by weight. Mixing with quartz sand is useful and economic for layers starting at 2 mm. The coating material has good processing-, free-flow-, and planar properties.
weberfloor 4761N epoxy coating has well balanced properties and may be used all-purpose. Because the product is multi-purpose and has a wide range of application possibilities the amount of material to be stored may be reduced. The cured coatings are very resistant to mechanical load and different chemicals. The coating is resistant to water, salt, salt solutions, alkaline and bases, as well as diluted mineral acids, like salt- or sulphuric acid. There is also a good resistance to many solvents like benzene, fuel, grease, oil, and so on. Conditional resistance to concentrated mineral acid. Short-term resistance to concentrated and diluted organic acids like formic or acetic acid. Nondurable resistance to chlorinated hydrocarbon, ester, concentrated nitric acid, and others. For special demands to resistance obtain advice.
weberfloor 4761N epoxy coating is available in different colours (RAL). Slight colour alterations may be possible due to technical reasons. Pale colour epoxy resin coatings may show slight colour alterations, which may become visible. For an epoxy resin product weberfloor 4761N epoxy coating shows only slight colour alterations though.
weberfloor 4761N epoxy coating has been successfully tested according to SOLAS MED IMO 2010 FTP Code and the testing program DIN EN 1504-2 in regard to DIN V 18026 “surface protection system for concrete with products according to DIN EN 1504-2”, in compliance with the test category OS 8 “chemical-resistant coating for areas with vehicle traffic and mechanical high load”. Ask for the tests reports.
- Thin coatings 0.8 - 1.5 mm for light mechanical load.
- Smooth coatings for commercially used areas with medium mechanical load, e.g. production areas, stacking ground in many economic sectors (2 mm coating).
- Smooth coatings for commercially used areas with high demands on mechanical load, e.g. production areas, stacking ground in many economic sectors (3 - 4 mm coating).
- Plain-coloured top sealer for scattered coatings.
- Pigmented supporting level for decorative, colour-sand scattered coatings and subsequent sealing coats, e.g. with weberfloor 4763N epoxy matt sealer.
- OS 8 coatings for areas with vehicle traffic and high mechanical load.
| Estimated consumption | Top coat: 0.550 - 0.900 kg/m² Thin coat: 0.8 - 1.5 kg/m² Standard coat: 1.3 - 1.5 kg/m² for each mm layer |
| Curing time for mechanical load | 48 - 72 hours at 20 °C |
| Curing time for chemical resistance | 7 days at 20 °C |
| Compressive strength | > 55 N/mm² |
| Flexural strenght | > 45 N/mm² |
See datasheet for more product spesifications.
- Good free-flow properties
- Guitable even for thin coatings
- Coloured glossy surface
- Wear-resistant / water and chemical resistant
- Solvent-free